Skip links and keyboard navigation

Station overview—The Gap

Location of The Gap

Map marker is indicative only. It does not reflect the exact location of the station.
See all stations in Mount Isa region.

The Gap station, established in 2009, is located in the grounds of the ‘Outback at Isa’ Centre in a residential area on the corner of Marian and Corbould Streets.

Monitoring period
1 April 2009–
Parameters monitored

Current measurements at 1am 20 October 2021

Air quality
ParameterMeasurementRunning average
Particle PM2.55.1µg/m³5.1µg/m³ (1hr avg)
Particle PM1012.9µg/m³12.9µg/m³ (1hr avg)
Sulfur dioxide0ppm0ppm (1hr avg)
Metals
ParameterMeasurementRunning average
Leadofflineoffline
Arsenicofflineoffline
Cadmiumofflineoffline
Copperofflineoffline
Zincofflineoffline
Nickelofflineoffline
Meteorological
ParameterMeasurement
Wind direction131deg
Wind speed1.3m/s
Temperature31°C

Legend to air quality category colours about category values

  • Good
  • Fair
  • Poor
  • Very poor
  • Extremely poor

None of the data is validated (0% validated, 0/12 records)

An offline message in a cell indicates that measurements are temporarily unavailable due to equipment servicing or failure. See network status.

About air quality categories

Air quality categories are used to make it easier to interpret air quality data by reducing the complexity associated with different pollutant concentration units and air quality guideline values.

Each air quality measurement from a monitoring station is assigned an air quality category rating based on comparison of the measurement value against the relevant air quality guideline. Five colour-coded air quality categories are used, being 'Good' (green), 'Fair' (yellow), 'Poor' (orange), 'Very Poor' (red) or 'Extremely Poor' (dark red). Values greater than the air quality guideline will be appear as ‘Poor’, ‘Very Poor’ or ‘Extremely Poor’.

More information about air quality categories.

About these parameters

Particle PM2.5

Airborne particles less than 2.5 micrometres in diameter, referred to as PM2.5, can be hazardous to human health or cause a nuisance when present in the air at elevated levels. They are capable of penetrating the lower airways of humans and can cause possible negative health effects.

The guideline for Particle PM2.5 is 50µg/m³ (1hr avg) and 25µg/m³ (24hr avg).

Particle PM2.5 is measured in micrograms per cubic metre.

More information about Particle PM2.5

Particle PM10

Airborne particles less than 10 micrometres in diameter, referred to as PM10, can be hazardous to human health or cause a nuisance when present in the air at elevated levels. They are capable of penetrating the lower airways of humans and can cause possible negative health effects.

The guideline for Particle PM10 is 100µg/m³ (1hr avg) and 50µg/m³ (24hr avg).

Particle PM10 is measured in micrograms per cubic metre.

More information about Particle PM10

Sulfur dioxide

Sulfur dioxide (SO2) is a colourless gas with a sharp, irritating odour. It is produced by burning fossil fuels and by the smelting of mineral ores that contain sulfur.

The guideline for Sulfur dioxide is 0.1ppm (1hr avg).

Sulfur dioxide is measured in parts per million.

More information about Sulfur dioxide

Lead

Lead is commonly used in manufacturing products like batteries and solders. The major emission source is from the mining, smelting and processing of mineral ores. Inhaling or consuming lead and its compounds can affect the human body, particularly the nervous system, and may result in growth and developmental problems in children.

The guideline for Lead is 2µg/m³ (24hr avg).

Lead is measured in micrograms per cubic metre.

More information about Lead

Arsenic

Elemental arsenic does not occur naturally but its compounds are widespread, often occurring with metal-bearing ores and released during processing. It is widely used in timber preservatives and pesticides, and is well-documented as an occupational hazard.

The guideline for Arsenic is 0.3µg/m³ (24hr avg).

Arsenic is measured in micrograms per cubic metre.

More information about Arsenic

Cadmium

Cadmium compounds occur naturally in the environment, particularly in areas of mineralisation. The major emission source is the processing of metal ores for lead, zinc and copper, where cadmium is a valuable by-product.

The guideline for Cadmium is 2µg/m³ (24hr avg).

Cadmium is measured in micrograms per cubic metre.

More information about Cadmium

Copper

Copper is one of a number of essential metals, and a small daily intake is required to maintain a healthy life. However, ingesting high levels of the element can lead to adverse health effects, as some of its compounds are toxic.

The guideline for Copper is 50µg/m³ (24hr avg).

Copper is measured in micrograms per cubic metre.

More information about Copper

Zinc

Zinc occurs widely in nature, and is another metal essential in trace quantities for good health. Exposure to elevated levels is more likely through occupational exposure in industry such as mining and smelting and processing of metal ores. Insufficient zinc intake has a detrimental effect on growth, and immune and reproductive system development. Adverse health effects generally only occur where the exposure is high.

The guideline for Zinc is 120µg/m³ (24hr avg).

Zinc is measured in micrograms per cubic metre.

More information about Zinc

Nickel

The guideline for Nickel is 0.12µg/m³ (24hr avg).

Nickel is measured in micrograms per cubic metre.

More information about Nickel

Wind direction

When high pollutant concentrations occur at a monitoring station, wind data records can determine the general direction and area of the emissions. Identifying the sources means planning to reduce the impacts on air quality can take place. The measurement indicates the direction the wind is coming from.

Wind direction is measured in degrees.

More information about Wind direction

Wind speed

When high pollutant concentrations occur at a monitoring station, wind data records can determine the general direction and area of the emissions. Identifying the sources means planning to reduce the impacts on air quality can take place.

Wind speed is measured in metres per second.

More information about Wind speed

Temperature

Measuring temperature supports air quality assessment, air quality modelling and forecasting activities.

Temperature is measured in degrees Celsius.

More information about Temperature

Licence
Creative Commons Attribution 4.0 International (CC BY 4.0)
Last updated
12 August 2020
  1. Is your feedback about:
  2. (If you chose ‘website’ above)

    Page feedback

    1. How satisfied are you with your experience today? *
  3. (If you chose ‘service’ above)

    Feedback on government services, departments and staff

    Please use our complaints and compliments form.